Pfaff Creative Deluxe Hoop 360 x 200mm.
Hoops the fabric for perfect stitching results for embroideries up to 360 x 200 mm. The Quick Release makes hooping easy.
Approx Size: 360 x 200mm (14.17 x 7.87 inches).
For Pfaff Models: Pfaff Creative Performance, Pfaff Creative Vision, Pfaff Creative Sensation, Pfaff Creative Sensation Pro, Pfaff Creative 4.5, Pfaff Creative 4.0.
Pfaff Creative Elite Hoop 260 x 200mm.
Update your PFAFF® creative vision™ sewing and embroidery machine and you will be able to use the new 260x200mm creative™ ELITE HOOP - perfect for that in-between size design. The creative™ ELITE HOOP features “Quick release” which makes re-hooping very easy. One snap of the quick release and your hoop is closed again and the fabric is tightened!
Approx Size: 260 x 200mm (10.24 x 7.88 inches).
The Pfaff creative Elite Hoop will fit the following machines: Pfaff Creative Sensation Pro, Creative Sensation, Creative Vision, Creative Performance, Creative 2.0, Creative 3.0, Creative 4.0, Creative 4.5.
Pfaff Passport 2.0 Straight Stitch Needle Plate.
The Straight Stitch Needle Plate guarantees even fabric feed at the beginning and end of a seam, while preventing the fabric from being pulled into the needle plate.
Fits the Pfaff Passport 2.0 ONLY.
Sometimes sewing heavier fabrics can affect the flow of your stitching. The Pfaff Grand Quilter has an additional embroidery darning foot and needle plate to eliminate any such problem. The embroidery foot is equipped with a pressure screw to allow you to adjust to the fabric being used. The needle plate is a screw on type giving it more stability when using heavier fabrics.
Pfaff Select Straight Stitch Needle Plate.
The Pfaff Straight Stitch Needle Plate guarantees even fabric feed at the beginning and end of a seam, while preventing the fabric from being pulled into the needle plate.
Fits the following Pfaff sewing machine models: Select 2.0, Select 3.0, Select 4.0, Select 2.2, Select 4.2, Select 3.2.
Pfaff Ruffler Attachment (Cat D).
With the Pfaff Ruffler, you can make closely or widely spaced pleats automatically while sewing. This is very useful for ruffles, frills, home decor, etc. The ruffler can be used in three different ways:
This foot will fit Category D machines.
Pfaff Ruffler Attachment (Cat G).
This foot will fit Category G machines.
Pfaff Ruffler Attachment (Cat C).
This foot will fit Category C machines.
Pfaff Select Creative Bobbin Case.
Create beautiful bobbin work, also called reverse decorative stitch embroidery, with the creative Bobbin Case. Depending on the type of decorative thread you are using for your projects, there are different ways of working with the Pfaff creative Bobbin Case.
For heavy or specialty threads:
Wind the bobbin with the decorative thread slowly. Place the bobbin in the Pfaff creative Bobbin Case. For less texture, use finer specialty threads and adjust the bobbin tension screw, if needed, so the thread pulls evenly and has a slight tension. Put the bobbin in the creative Bobbin Case and
pull the specialty thread into the bobbin tension.
For heavier yarns and textured specialty threads:
Wind the bobbin evenly clock-wise by hand. Put the bobbin in the Bobbin Case. For the most textured bobbin work, do not pull the heavy thread or yarn into the bobbin tension, but go directly into the bypass slot. To bring up the bobbin thread, hold the needle thread, and turn the handwheel towards you.
1. Thread the top with regular sewing thread.
2. Use the recommended size needle for your fabric.
3. Snap on the presser foot 2/2A or 8.
4. Place the right side of the fabric facing down and place Tear Away Stabilizer on top.
5. Select stitches where the density is loose. Experiment with the straight stitch, zigzag and decorative stitches. Increase the stitch length for best results.
6. Select slow speed and stitch at an even speed.
7. Increase needle thread tension slightly if needed.
This Case will fit with the following machines:
Pfaff Blindhem and Lace Foot.
The Blindhem Foot is used to sew blindhems and decorative stitches. The blind hem will make the stitches almost invisible from the right side of the garment.
1. Set the overlock machine for the desired stitch.
2. Snap on the Blindhem Foot.
3. Fold and press the hem in place. Turn the hem back on itself toward the right side of the
fabric. Leave ¼” (6mm) of the edge exposed. (See illustration.)
4. Place the hem under the foot with the fold against the guide on the foot.
5. Loosen the guide screw to adjust the guide so that the needle just catches the thread of the
6. Guide the fabric as you sew, making sure the fold of the fabric is always against the guide.
7. Open the fabric and press lightly on the wrong side.
8. Test on a scrap piece of fabric before sewing your project.
1. Set the overlock machine for the desired stitch
2. Snap on the Blindhem Foot.
3. Place the wrong side of the lace to the right side of the fabric.
4. Place under the foot with the fabric extending to the right of the guide. The header of the
lace will be against the left side of the guide.
5. Loosen the guide screw to adjust the guide so the needle just catches the header of the lace.
6. Guide the fabric as you sew, making sure the header of the lace is always against the
7. When finished, open the lace flat. Fold the seam allowance to the back of the fabric and
8. If using insertion lace, repeat on the other side of the lace.
For Pfaff Overlockers: Coverlock 4.0, Coverlock 3.0 & Hobbylock 2.5.
With the Pfaff Flat Trim Foot, you can easily add lace and trims to the top of the fabric with a coverstitch to create beautiful decorative edges and effects.
1. Set the machine for a Coverstitch wide.
2. Snap on the Flat Trim foot.
3. Use default stitch settings. Adjust if needed.
4. Insert the fabric edge into the lower section on the left side of the foot. Slide the fabric under the foot and under the needles.
5. Insert the trim into the upper section on the right side of the foot. Slide the trim toward the back of the foot beyond the needles, leaving a short tail of trim behind the needles. while sewing.
Tip: Use tweezers to slide the fabric andthe trim to the correct position under the needles.
6. Lower the needles into the trim and the fabric. Lower the Flat Trim foot
7. As you sew, hold the fabric in your left hand and the trim in your right hand.
Tip: If you want a finished fabric edge, press a ¼” (6mm) hem to the right side of the fabric before inserting the fabric into the Flat Trim foot. The lace will cover the fabric raw edge when sewn in place.
For Pfaff Overlockers: Coverlock 3.0 & Coverlock 4.0.
The Pfaff Piping foot with Cording guide, you can create piping, corded tucks and decorative trims.
Easily create your own piping:
1. Set the machine for Chainstitch.
2. Use the default stitch settings. Adjust if needed.
Note: Although the machine recommends needle D, you will use needle E for this technique instead.
3. Snap on the Piping foot. (The cording guide is not used for this technique.)
4. Place the cord in the groove on the bottom of the foot and pull the cord tail behind the foot about 2½” (5cm).
Note: ¼” - 5/8” (1.5 - 2.0mm) cord can be used.
5. Cut a strip of fabric on the bias, 1” (25mm) wide.
6. Wrap the fabric around the cord in the front of the foot. Slide the fabric under the foot.
7. Lower the presser foot and sew over the cord and fabric. (Hold the cord behind the foot as you begin to sew.)
Achieve a trapunto effect when a coverstitch is sewn over a cord in the guide.
1. Set the machine for coverstitch, wide.
Note: Although the machine recommends needles C and E, you will use needles D and E for this technique instead.
2. Snap on the Piping foot and attach the cording guide.
3. Insert the cord into the round hole of the cording guide and position it in the groove on the bottom of the Piping foot.
4. Lay the fabric right side up on top of the cord. Slide it under the foot until it is underneath the needles.
5. Lower the needles into the fabric. Lower the presser foot and start to sew at a medium speed. (Hold the cord behind the foot as you begin to sew.)
Use decorative thread and ribbons to create special effects and unique trims.
1. Set the machine for 3-thread ornamental fl atlock stitch, wide with decorative thread in the loopers.
2. Snap on the standard presser foot and attach the cording guide as illustrated.
3. Insert a ribbon ¼” (6mm) wide right side down into the rectangular opening in the guide.
4. Place the ribbon under the presser foot to the right side of the needle, leaving a 2” (5cm) tail behind the foot.
5. The needle should go down into the machine just beyond, not into, the edge of the ribbon.
6. Sew over the ribbon to make a decorative trim.
Tip: Make your decorated
Pfaff Free Motion Quilting Foot (Cat D).
The Free-motion/Darning Foot is perfect for sewing free-motion embroidery or darning.
1. Make sure the needle is at its highest position.
2. Attach the Darning Foot: with your thumb and finger, squeezing the front and back of the foot together. Insert the pin of the Darning
Foot as far as it will go into the hole at the back of the presser foot holder.
3. The “C-shaped” Guide should be positioned around the presser bar. The long arm must be behind the needle clamp. Tighten the screw.
4. Lower the feed dogs.
5. If you like, you can hoop the project in a round embroidery hoop for more stability.
6. Select a straight stitch and activate the free-motion function, or put the presser foot in the darning/free-motion position.
7. Pull up the bobbin thread and sew a few stitches to secure. Clip the thread ends close to the project and continue sewing.
Note: Remember, when sewing with the feed dogs lowered, the stitch length is determined by you. An even, medium-to-fast sewing speed
will allow you to sew a more consistent length of straight stitch. Sewing too slowly may cause small knots to appear on the reverse side of your work.
The Pfaff Grand Quilter 1/4 Inch Foot sews a 1/4 seam allowance quickly and accurately. Great for piecing quilts and topstitching. For Pfaff Grand Quilter sewing machine.
Pfaff Free Motion Quilting Foot (Cat G).
Pfaff Free Motion Quilting Foot (Cat C).
Pfaff Fancy Stitch Foot with IDT (Cat D).
Create beautiful embellishments with the Fancy Stitch Foot. This foot has easily visible marking to help you position decorative stitches or borders on your fabric. A special groovy on the bottom allows optimal feed of even the most densely stitched patterns.
Pfaff Fancy Stitch Foot with IDT (Cat J).
This foot will fit Category J machines.
Pfaff Embroidery / Sensormatic Free Motion Foot (Cat J).
The Sensormatic free-motion foot is used for stippling and free-motion embroidery. The foot allows for greater visibility for both stippling and free-motion embroidery. When sewing free-motion at a low speed the presser foot will raise and lower with each stitch to hold the fabric on the stitch plate while stitch is being formed. At higher speed, the presser foot floats over the fabric while sewing.
For Pfaff Category J Machines.
Will NOT Fit: Expression 3.2, 3.0, 2.0 & Expression 150.
Pfaff 1/4 Inch Quilting Foot with IDT (Cat J).
A quilt consists of two layers of fabric with a layer of batting sandwiched between them. Many pieces of fabric can be joined together in continually changing patterns to form the top layer of the quilt. The 1/4 inch quilting foot is particularly suitable for joining these pieces of fabric. The clearance between the needle and the outer edge of the foot is 1/4 inch (6.3mm) and between the needle and the inner edge of the foot 1/8 inch (3.15mm).
1. Attach the 1/4 inch Quilting Foot.
2. Engage the IDT™ system, if available on your machine.
3. Sew fabric together using straight stitch.
4. When using 1/4 inch seam allowance, guide fabric along outer edge of foot. When using a
1/8 inch seam allowance, guide fabric along inner edge of foot.
This will fit Category J machines.
Pfaff Three Hole Yarn Foot with IDT (Cat J).
Embellish your project with different types of decorative cords or yarn using beautiful PFAFF® 9 mm stitches and the Three Hole Yarn Foot. This foot will easily guide the cords or yarn through the openings in the front of the foot back through the groove under the presser foot. The decorative cords or yarn will be stitched over creating a beautiful braid embellishment.
1. Thread your machine with a regular sewing thread or decorative thread on top and regular sewing thread in the bobbin.
2. Select a 9 mm decorative stitch. Note: Decorative stitches that use forward motion work best (Avoid stitches with too much backward motion.)
3. Thread decorative cords or yarn into the holes from the top of the foot, using the Yarn Threader, prior to attaching the foot onto the sewing machine.
4. Make sure the cords or yarn slide easily through the openings. (If the yarn is too thick it will create too much tension and the feeding might be affected.)
5. Snap on the Three Hole Yarn Foot.
6. Engage IDT™ system.
7. Place the threaded cords or yarn under the presser foot with a 5 cm (2”) tail.
8. Place a tear away stabilizer underneath the fabric and place your fabric under the presser foot.
9. Sew carefully, not too fast. If your machine has a speed control reduce the sewing speed to easily guide the fabric and yarn as you sew.
This foot will fit Category J Machines.
Pfaff Fancy Stitch Foot with IDT (Cat K).
This foot will fit Category K machines.
Pfaff Fancy Stitch Foot with IDT (Cat G).
Pfaff 1/4 Inch Quilting Foot with IDT (Cat K).
This will fit Category K machines.
Pfaff 1/4 Inch Quilting Foot with IDT (Cat D).
This will fit Category D machines.
Pfaff 1/4 Inch Quilting Foot with IDT (Cat G).
This will fit Category G machines.
The Bridging Guide F2 is used with the Transparent Presser Foot F (standard accessory) to join two finished pieces of fabric with consistent space between. The coverstitch looper thread is the one visible in the open area. This is a great place to weave a narrow ribbon or decorative thread.
Pfaff Fancy Stitch Foot (Cat J).
Pfaff Fancy Stitch Foot (Cat G).
Pfaff Clearview foot (Cat C).
Use the Clearview Foot when sewing decorative stitches to have an optimal view of the embroidery area. You'll be able to sew beautiful embellishments. This foot has easily visible markings to help you position decorative stitches or borders on your fabric. A special groove on the bottom allows even densely stitched patterns to be fed perfectly.
This foot will fit the Pfaff Category C machines.
Under cover padding only, fits 67cm Pfaff roller irons.
This fits the Pfaff roller Iron 560, Roller Press, 658, 654 and 652.
Pfaff Beading Foot.
This foot is used for sewing on beads, spangles, etc.
Preparing the machine
• Needle: Left or right (left is preferable.)
• Stitch type: Three-thread overlock or wrapped edge overlock
• Stitch length: 3-5mm
• Differential feed lever: Normal position
• Upper knife: Working or non-working position
1. Select sewing method (A) or (B), then determine needle position and sew 2 or 3 stitches.
2. Turn hand wheel with hand until needle point is level with fabric surface on its upward stroke.
Then insert the end of string of beads into guide on presser foot.
3. Sew 2 - 3 stitches by turning hand wheel with hand.
4. Press beards lightly with left finger while sewing.
5. Sew the last few stitches by turning hand wheel with hand to avoid beads interfering with needle
For the Pfaff Overlocker: Hobbylock 2.0.
Pfaff Twin Welting Foot (Cat J).
The Pfaff Welting Foot and the Twin Welting Foot are used to make rim for your home dec projects like pillows, cushions and other home accessories. you can also make trim cover raw edges on your upholstery, which you can then attatch with a staple gun. It's quick and easy to make and insert welt cording. The Welting Foot works the same way as the Piping Foot but is designed for larger sizes of cording. Create your own trim when the colour you want isn't available.
1. Make bias strips long enough to cover the cords and wide enough to wrap around the two
cords plus seam allowance.
2. Place the cords on the wrong sides of the bias strip – side to side - and wrap the fabric around
3. Place the fabric and cord under the presser foot with the right cord under the left groove of the
foot, and the raw edges to the right.
4. Adjust to center needle position – straight stitch and stitch length 3.
5. Keep the cords against the fold as you sew.
6. Trim the fabric close to the seam and press seam allowance to the left.
7. Wrap the excess fabric to the center back of the cord.
8. Put the covered cord under the two grooves of the presser foot and sew it onto your sewing
Pfaff Twin Welting Foot (Cat K).
Pfaff Twin Welting Foot (Cat C).
Pfaff Twin Welting Foot (Cat D).
Pfaff Twin Welting Foot (Cat G).
Pfaff Beading Foot 4mm (Cat J).
For that extra touch, highlight any sewing project with strings of pearls or beads. The beads will run smoothly through the groove under the foot while you sew for beautiful results.
1. Snap on the Beading Foot.
2. Thread your machine with invisible thread in the needle and regular sewing thread that matches the fabric in the bobbin.
3. Select one of the following stitches depending on which is available on your machine. Adjust the settings of the stitch according to the size of the beads.
For 4 mm beads
Zigzag stitch length 3.5 width 4.0
Blindhem stitch length 1.0 width 4.5
4. Lower the needle thread tension to achieve a beautiful stitch.
5. Place stabilizer under the fabric and position both under the foot.
6. Place the bead string under the foot in the groove on the underside of the beading foot. Lower the presser foot.
7. Turn the hand wheel to create manual stitches to set the beads in place.
8. Stitch slowly.
Note: Stitch the bead string to a scrap piece of fabric first to test thread tension, stitch length and stitch width according to the beads and the fabric. Make adjustments as needed.
Pfaff Piping Foot (Cat J).
Insert packaged piping into seams and edges for a tailored finish. Cover cord with fabric for specialty piping.
To stitch piping into a seam:
1. Snap on the Piping Foot.
2. Place piping along the seam line on right side of fabric. Place second piece of fabric on top with
right sides together.
3. Put fabric and piping layers under Piping Foot with the piping in the groove on the under- side of
the foot. Sew with a straight stitch, length 2.5. The groove on the underside of the foot will
guide the piping as you sew.
To make piping from your fabric:
1. Cut bias or crosswise grain strips, wide enough to cover the cording plus seam allowances.
2. Lay the cording on the wrong side of the fabric strip and wrap the fabric over the cord.
3. Place the fabric and cord under the Piping Foot with the cord in the groove on the under- side of
4. Stitch. The groove will guide the cord so the fabric covers evenly.
TIP: When you sew this piping into a garment, adjust
Pfaff Beading Foot 4mm (Cat C).
For Pfaff Category C Machines.
Pfaff Beading Foot 4mm (Cat K).
For Pfaff Category K Machines.
Pfaff Beading Foot 4mm (Cat D).
For Pfaff Category D Machines.
Pfaff Beading Foot 4mm (Cat G).
For Pfaff Category G Machines.
Pfaff Piping Foot (Cat K).
Pfaff Piping Foot (Cat C).
Pfaff Piping Foot (Cat D).
Pfaff Piping Foot (Cat G).
Pfaff 1/4 Inch Seam Foot.
A popular foot with patchworkers for that essential 1/4 inch seam. The guide on the foot enables you to sew a perfect 1/4 inch seam every time. No patchworker should be without one.
Will only fit the Pfaff Hobby 1122, 1132, 1142.